14. 站点编程 / PROGRAMMING SITES
对应 PDF 第 38–40 页
Press Menu → Manage Favorites → Favorites List → Review/Edit System → System → Edit Site. To Create a New Site, scroll to New Site and press E/yes. To Edit an Existing Site, scroll to the Site and press E/yes. Note:
Not all options will appear for all sites.
路径： Menu → Manage Favorites → 列表 → Review/Edit System → 系统 → Edit Site → 新建/选择站
点。注意：并非所有选项对所有站点类型都出现。
| 选项 / Option | 英文原文（EN） | 中文译文（CN） |
|---|---|---|
| Edit Name | See Data Naming. | 站点命名。 |
| Set Site Type（仅 EDACS） | EDACS Wide is the same as EDACS Standard and use a 9600 baud control channel. EDACS Narrow- band sites use a 4800 baud control channel. Wide (Standard) or Narrow. The default setting is Wide. | EDACS 站点类型：Wide（标准， 9600 波特控制信道，默认）/ Narrow （窄带，4800 波特）。 |
| Edit Band Plan（仅 Motorola/P25） | Band plans are required so the scanner can correctly determine the voice channel frequencies. P25 Systems: Explicit mode systems (which comprise most systems in use) include all information needed to determine voice frequencies on the control channel, leave all entries blank. The system will automatically detect the band plan and fill in the entries. Implicit systems need you to supply the systems band plan with the Custom option. Select Plan: Scroll to each Band Plan 0-9, A-F, and press E/yes. Input Base Freq: Enter the base frequency. Input Spacing: Enter the step size. Motorola Systems: 800/900 Standard or 800 Splinter. Custom Motorola/VHF/UHF Systems: Custom band plans require that you enter both a lower and an upper base frequency value. Use the Excel spreadsheet or Band Plan Calculator at info.uniden.com to calculate the upper base frequency. Select Plan 1-6. Set Base Freq: Input Lower / Input Upper. Set Offset: Input Offset; Select Polarity (+ or -). Set Spacing. Press Menu to return and repeat for each band plan as needed. | 频段表（Band Plan）用于正确推算话 音信道频率。P25 系统：显式 （Explicit）系统（大多数）会在控制 信道自带全部信息，留空即可自动检 测；隐式（Implicit）系统需用 Custom 手工输入：选频段表 0–9、 A–F → 输入基准频率 → 输入步进。 Motorola 系统：可选 800/900 Standard（标准）或 800 Splinter （裂频）；自定义 VHF/UHF 频段表需同时输入上下两个基准频率（下基准即 RR 数据库提供的 base），上基准可用 Uniden 官方 Excel 计算器 （info.uniden.com 搜索 CalculatingUpperBaseFrequencies） 计算：选计划 1–6 → 输入 Lower/Upper → 输入偏移与极性 （+/-）→ 输入步进。 |
| Set Frequencies | This is where you program trunking frequencies for the Site. New Frequency/Edit Frequency: Enter the frequency and press E/yes. For EDACS and LTR sites only: Input LCN: Enter the LCN number and press E/yes. Delete Frequency. | 编程站点集群频率：新建/编辑频率； EDACS 与 LTR 站点必须输入 LCN （逻辑信道号）；可删除频率。 |
| Set Modulation（无 P25/P25 单频） | This setting selects the modulation used for the Site. The default setting is Auto. Auto, NFM, or FM. | 站点调制：Auto/NFM/FM（默认 Auto）。 |
| Set Attenuator | This setting controls whether the scanner attenuates signals on the Site by about 20 dB. The default setting is Off. On or Off. | 站点衰减约 20dB：开/关（默认关）。 |
| Set Avoid | This determines whether a Site will be scanned or not. Temporary Avoids cancel when you cycle power. The default setting is Stop Avoiding. Stop Avoiding, Temporary Avoid, or Permanent Avoid. | 站点回避：停止/临时/永久（默认停止 回避）。 |
| Set Location Information | This allows you program a location for the Site to use with Location Control enabled or with a GPS. You can program a circle with a radial range or multiple rectangles as a location. See Set Up GPS first to set your location format and the Baud rate. Circle: Set Latitude; Set Longitude; Set Range 0-6000. Rectangles: New Rectangle – Latitude/Longitude Top Left, Latitude/Longitude Bottom Right; Stored Rectangle – Edit Rectangle; Delete Rectangle. | 为站点编程位置（供位置控制/GPS 使 用）。可编程圆形（纬/经度+范围 0– 6000）或多个矩形（左上角/右下角经 纬度，可编辑/删除已存矩形）。先 按"Set Up GPS"设置位置格式与波特 率。 |
| Digital Waiting Time（仅 Motorola） | Same as System option (above); default 400 ms; 0 to 1000. | 同系统级"数字等待时间"（默认 400ms，0–1000）。 |
| Digital Threshold Mode / Level （P25/Motorola/MOTOTRBO） | The default setting is Auto. Auto / Manual / Default (threshold 8). Digital Threshold Level – default 8; 0 to 20. | 数字阈值模式/电平： Auto/Manual/Default；电平 0–20 （默认 8）。 |
| Delete Site / New Site | Deletes the Site. At Confirm Delete? press E/yes or ./no. / See New Site. | 删除站点（有确认提示）/ 新建站点。 |