23. 搜索/Close Call 选项 / SEARCH / CLOSE CALL OPTIONS
对应 PDF 第 60–61 页
These are the settings you should look at before you perform a Quick Search, or Close Call Search. Press Menu.
Scroll to Srch/CloCall Opt and press E/yes.
执行快速搜索或 Close Call 搜索前建议先检查这些设置。路径： Menu → Srch/CloCall Opt（搜索/Close Call 选项）。
| 选项 / Option | 英文原文（EN） | 中文译文（CN） |
|---|---|---|
| Freq Avoids | This allows you to review Avoided Frequencies or Stop Avoiding all Frequencies for Searching and Close Call search. Temporary Avoids appear reversed in the display. Stop All Avoiding – At Confirm? Press E/yes or ./no. Rvw Search Avoid – Scroll to Frequency and press E/yes to Stop Avoiding. See also Search Avoids. | 查看/解除搜索与 CC 搜索中被回避的频 率（临时回避反白显示）：Stop All Avoiding=全部解除（有确认）；Rvw Search Avoid=逐个解除。 |
| Broadcast Screen | Automatically ignores transmissions that are on common broadcasts, paging systems, and other annoyance radio sources during Custom Search, Quick Search, or Close Call Search. The default setting is Pager On. Set All Band On/Off. Set Each Band – Scroll to each Band and press E/yes to enable or disable. Program Band – Band 0-9; Set Lower Limit; Set Upper Limit; Press Menu to return and repeat for each band as needed. | 广播过滤：在自定义/快速/CC 搜索中自 动忽略常见广播、寻呼及其他干扰源 （默认 Pager=On）。可全部频段开 关、逐频段开关，并编程自定义频段 （Band 0–9，设上下限）。 |
| Repeater Find | Sets whether the scanner tries to tune to a repeater output frequency when it detects a transmission on a repeater input frequency, in Search and Close Call modes. Turning this feature on can let you hear both sides of the conversation on the output frequency. The default setting is Off. On or Off. | 中继搜索：搜索/CC 模式中检测到中继 上行频率时自动转至下行输出频率收听 双方通话。默认关。 |
|---|---|---|
| Set Delay Time | Determines how long the scanner waits after a transmission ends before resuming Quick Search and Close Call Search operations. A negative delay will force a resume after that number of seconds. The default setting is 2 seconds. -10, -5, 0, 1, 2, 3, 4, 5, 10, or 30 sec. | 快速搜索/CC 搜索在信号结束后的恢复 延迟：-10～30 秒（负值=强制恢 复），默认 2 秒。 |
| Set Attenuator | This controls the attenuator for Quick Search, and Close Call operations by about 20dB. The default setting is Off. On or Off. | 快速搜索/CC 搜索衰减约 20dB，默认 关。 |
| Set Audio AGC | This allows you to turn AGC (Automatic Gain Control) on or off for Quick Search and Close Call modes. The default settings are Off. Analog – press E/yes to toggle. Digital – press E/yes to toggle. | 快速搜索/CC 模式的音频自动增益控制 （AGC）：模拟/数字分别开关，默认 关。 |
| Digital Waiting Time | This setting gives the scanner time to determine if frequencies have digital or analog transmissions. During this time, the scanner will evaluate the received signal and, if it detects digital data, will open squelch immediately. If digital is not detected before the delay expires, the scanner will open squelch at the end of this delay. This is to prevent "false decode" problems. The default setting is 400 ms. 0 to 1000 ms. Note: Any analog transmissions will lose the first part of the transmission, up to the wait time you set here. | 数字等待时间：判别信号为数字还是模 拟的等待时长（0–1000ms，默认 400）。期间检测到数字数据立即开静 噪；超时未检测到则到时开静噪，防 止"误解码"。注意：模拟信号会因此丢 失开头最多等于等待时长的一部分。 |
| Digital Threshold Mode | The default setting is Auto. Auto – Automatically sets the decode threshold based on the received signal. Manual – Allows you to manually set the threshold in threshold setting mode or using the Digital Threshold Level setting. Default – Sets the scanner to the default threshold of 8, Auto. | 数字阈值模式：Auto=自动（默认）； Manual=手动（配合 Digital Threshold Level）；Default=恢复默 认阈值 8。 |
| Digital Threshold Level | The default setting is 8. 5 to 13. | 数字阈值电平：5–13，默认 8。 |