本章说明 IC-7300 的 CI-V 遥控接口：怎样用 USB 线把电脑（controller）与 IC-7300 连起来，遥控之前必须先在 SET 模式里 设定好地址、通信速度与 transceive 功能。本章给出 CI-V 命令的数据格式——Controller → IC-7300 的 7 字节帧，以及 IC- 7300 → Controller 的 OK （ FB ） / NG （ FA ） 5 字 节 应 答 帧 。 随 后 是 完 整 的 命 令 表 ， 按 Cmd. ／ Sub cmd. ／ Data ／ Description 四列列出频率、工作模式、VFO、存储通道、扫描、音量与增益、AGC 与滤波器、Scope、RTTY、录音、CI-V 地 址与波特率等全部指令，可直接当作编写遥控程序的字典使用。命令号后带星号（*）的命令为可发送/可读取（Send/read）命 令。This chapter describes the IC-7300's CI-V remote control interface: how to connect the PC (controller) to the IC- 7300 with a USB cable, and which settings—address, data communication speed and the transceive function—must be made in Set mode before controlling the transceiver. The CI-V data format is given here: the 7-byte frame sent from the Controller to the IC-7300, and the 5-byte OK (FB) / NG (FA) reply frames sent back from the IC-7300 to the controller. The complete command table then lists every command in four columns—Cmd., Sub cmd., Data and Description—covering frequency, operating mode, VFO, memory channels, scanning, level and gain settings, AGC and filters, the Scope, RTTY, recording, and the CI-V address and baud rate. It can be used directly as the reference dictionary when writing remote control software. Commands marked with an asterisk (*) after the command number are Send/read data commands.
19-2 Remote control (CI-V) information · 遥控（CI-V）信息
CI-V 连接 CI-V connection
The transceiver's operating frequency, mode, VFO and 收发信机的工作频率、工作模式、VFO 以及存储通道的选 memory selection, can be remotely controlled using a PC. 择，都可以用电脑进行遥控。
• Use a USB cable (user supplied) to connect the IC-7300 • 用 一 条 USB 线 （ 用 户 自 备 ） 把 IC-7300 与 电 脑 and the PC (controller). （controller）连接起来。 The required USB driver and driver installation guide can 所需的 USB 驱动及其安装指南可从 Icom 网站下载。 be downloaded from the Icom web site. https://www.icomjapan.com/support/firmware_driver/ https://www.icomjapan.com/support/firmware_driver/
图 19-1 CI-V 连接示例（IC-7300 的 [USB] 端口 ↔ 电脑 USB 端口） CI-V connection example (the IC-7300 [USB] port to a PC USB port)
提示 NOTE NOTE 连接线尽量短。USB 线过长时，电脑可能识别不到收发信机。 Make the connection as short as possible. The transceiver may not be recognized by the controller, depending on the USB cable length.
提示 NOTE NOTE 网页上的下载步骤可能不经通知即行变更。 The download procedure on the web page may be changed without notice.
火腿经验 HAM TIP HAM TIP 设置备份做「三件套」：SD 卡存一份设置数据、屏幕截图留证，再在笔记本上记下 CI-V 地址——IC-7300 的默认地址是 94 （收发信机）与 E0（控制器）。将来换机器、重装驱动或者写程序联调，这三个地址/设置能省下大量时间。 Back up your settings the "three-piece way": store the setting data on an SD card, keep screenshots as evidence, and write the CI-V addresses down in your notebook—the IC-7300 default addresses are 94 (transceiver) and E0 (controller). These three items save a lot of time when you change computers, reinstall drivers, or debug your own programs.
准备 Preparing
The Icom Communications Interface V (CI-V) is used for 本机使用 Icom Communications Interface V（CI-V）进 remote control. 行遥控。
To control the transceiver, first set its address, data 要遥控本机，必须先设定它的地址、数据通信速度以及 communication speed, and transceive function. These transceive 功能。这些设定在 SET 模式中进行。 settings are set in Set mode.
数据格式 Data format
The CI-V system can be written using the following data CI-V 系 统 可 用 下 列 数 据 格 式 编 写 。 数 据 格 式 依 命 令 号 formats. Data formats differ according to command （command number）而异；部分命令还会再加上数据 numbers. A data area or sub command is added for some 区 （ data area ） 或 子 命 令 号 （ sub command commands. number）。
表 19-1 CI-V 命令格式：Controller → IC-7300 CI-V command format: Controller to IC-7300
序号 字节 说明 No. Byte Description
① ② FE FE 前导码（固定） Preamble code (fixed)
③ 94 收发信机默认地址 Transceiver's default address
④ E0 控制器默认地址 Controller's default address
⑤ Cn 命令号（见命令表） Command number (see the command table)
⑥ Sc 子命令号（见命令表） Sub command number (see command table)
⑦ Data area 用于输入频率或存储号的 BCD 码数据 BCD code data for frequency or memory number entry
— FD 报文结束码（固定） End of message code (fixed)
表 19-2 CI-V 命令格式：IC-7300 → Controller（OK 报文，5 字节） CI-V command format: IC-7300 to controller (OK message, 5 bytes)
序号 字节 说明 No. Byte Description
① ② FE FE 前导码（固定） Preamble code (fixed)
③ E0 控制器默认地址 Controller's default address
④ 94 收发信机默认地址 Transceiver's default address
⑤ FB OK 码（固定）——送至控制器的 OK 报文 OK code (fixed) — OK message to controller
— FD 报文结束码（固定） End of message code (fixed)
表 19-3 CI-V 命令格式：IC-7300 → Controller（NG 报文，5 字节） CI-V command format: IC-7300 to controller (NG message, 5 bytes)
序号 字节 说明 No. Byte Description
① ② FE FE 前导码（固定） Preamble code (fixed)
③ E0 控制器默认地址 Controller's default address
④ 94 收发信机默认地址 Transceiver's default address
⑤ FA NG 码（固定）——送至控制器的 NG 报文 NG code (fixed) — NG message to controller
— FD 报文结束码（固定） End of message code (fixed)
说明 NOTE NOTE
表 19-1 是 Controller 发给 IC-7300 的命令帧： FE FE 前导码 → 94 收发信机地址 → E0 控制器地址 → Cn 命令号 → Sc 子命令号 → 数据区 → FD 结束。表 19-2 与表 19-3 是 IC-7300 的应答帧，地址方向相反（ E0 在前、 94 在 后），只有第 5 个字节不同： FB 表示 OK（命令被接受）， FA 表示 NG（命令不被接受）。这两帧都不带数据区，长度 固定为 5 字节。
Table 19-1 is the command frame sent from the Controller to the IC-7300: FE FE preamble, 94 transceiver address, E0 controller address, Cn command number, Sc sub command number, data area, and FD end of message. Tables 19-2 and 19-3 are the reply frames from the IC-7300, in which the address order is reversed ( E0 first, 94 second); only the fifth byte differs: FB for OK (the command was accepted) and FA for NG (the command was not accepted). Neither reply frame carries a data area, and both are fixed at 5 bytes.
火腿经验 HAM TIP HAM TIP CI-V 控制最大的坑是「两个虚拟 COM 端口」。装好 USB 驱动后，Windows 会建出两个串口，但只有一个真正受 DTR/RTS 控制、能用于 CI-V。写程序连不上时，先到设备管理器里把两个端口逐个试一遍；也可以按第 20 章的方法改端口号。另一个 常见坑是波特率与 transceive 设置——SET 模式里的 CI-V Baud Rate 和 CI-V Transceive 必须与程序里写的一致，否则一个 字节都收不到。 The biggest trap in CI-V control is the "two virtual COM ports". Once the USB driver is installed, Windows creates two serial ports, but only one of them is actually controlled by DTR/RTS and can be used for CI-V. If your program cannot connect, try each port in turn in the Device Manager; you can also change the port number as described in chapter 20. Another common trap is the baud rate and the transceive setting—the CI-V Baud Rate and CI-V Transceive items in Set mode must match what the program uses, otherwise not a single byte gets through.
命令表 Command table
The command table lists the Cmd., Sub cmd., Data and 下 面 的 命 令 表 列 出 每 一 条 CI-V 命 令 的 Cmd. 、 Sub Description of every CI-V command. An asterisk (*) after a cmd.、Data 与 Description。命令号后面的星号（*）表 command number means that the command is a 示该命令为可发送/可读取（Send/read data）的命令。 Send/read data command.
表 19-4 CI-V 命令表（Cmd 00 ~ 0F） CI-V command table (Cmd 00 ~ 0F)
Sub Cmd. Data 说明 cmd. Cmd. Data Description Sub cmd.
00 p. 19-9 发送频率数据（transceive） Send frequency data (transceive)
p. 19-9 发送模式数据（transceive） Send mode data (transceive)
p. 19-9 读取波段边界频率 Read band edge frequencies
p. 19-9 读取工作频率 Read operating frequency
p. 19-9 读取工作模式 Read operating mode
p. 19-9 设定工作频率 Set operating frequency
p. 19-9 transceive 的工作模式选择 Operating mode selection for transceive
07 00 选择 VFO A Select VFO A
01 选择 VFO B Select VFO B
A0 使 VFO A 与 VFO B 相同 Equalize VFO A and VFO B
B0 交换 VFO A 与 VFO B Exchange VFO A and VFO B
08 00 00 01 to 00 99 选择存储通道 *(00 01=M-CH01, 00 99=M-CH99) Select the Memory channel *(00 01=M-CH01, 00 99=M-CH99)
01 00 选择编程扫描边界通道 P1 Select program scan edge channel P1
01 选择编程扫描边界通道 P2 Select program scan edge channel P2
09 存储写入 Memory write
0A 存储内容复制到 VFO Memory copy to VFO
0B 清除存储内容 Memory clear
0E 00 停止扫描 Scan stop
Sub Cmd. Data 说明 cmd. Cmd. Data Description Sub cmd.
01 启动编程扫描/存储扫描 Programmed/memory scan start
02 启动编程扫描 Programmed scan start
03 启动 ∂F 扫描 F scan start
12 启动细调编程扫描 Fine programmed scan start
13 启动细调 ∂F 扫描 Fine ∂F scan start
22 启动存储扫描 Memory scan start
23 选择存储扫描的起始通道 Select memory scan start
A1 选择 ∂F 扫描跨度 ±5 kHz Select ∂F scan span ±5 kHz
A2 选择 ∂F 扫描跨度 ±10 kHz Select ∂F scan span ±10 kHz
A3 选择 ∂F 扫描跨度 ±20 kHz Select ∂F scan span ±20 kHz
A4 选择 ∂F 扫描跨度 ±50 kHz Select ∂F scan span ±50 kHz
A5 选择 ∂F 扫描跨度 ±100 kHz Select ∂F scan span ±100 kHz
A6 选择 ∂F 扫描跨度 ±500 kHz Select ∂F scan span ±500 kHz
A7 选择 ∂F 扫描跨度 ±1 MHz Select ∂F scan span ±1 MHz
B0 设为非选择通道 Set as non-select channel
B1 设为选择通道 (用 CI-V 先前设定的号码会在电源开启后恢复；若未进行选择，则选中「1」) Set as select channel (The previously set number by CI-V is set after turning power ON, or "1" is selected if no selection is performed.)
01 to 03 设为选择通道 *(01=SEL1, 02=SEL2, 03=SEL3) Set as select channel *(01=SEL1, 02=SEL2, 03=SEL3)
B2 00 to 03 设为选择存储扫描对象 *(00=ALL, 01=SEL1, 02=SEL2, 03=SEL3)
Sub Cmd. Data 说明 cmd. Cmd. Data Description Sub cmd.
Set for select memory scan *(00=ALL, 01=SEL1, 02=SEL2, 03=SEL3)
D0 设定扫描继续功能 OFF Set Scan resume OFF
D3 设定扫描继续功能 ON Set Scan resume ON
0F 00/01 读取异频（SPLIT）设定（00=OFF, 01=ON） Read Split setting (00=OFF, 01=ON)
00 关闭异频功能 Turn the split function OFF
01 开启异频功能 Turn the split function ON
表 19-5 CI-V 命令表（Cmd 10* ~ 16*） CI-V command table (Cmd 10* ~ 16*)
Cmd. Sub cmd. Data 说明 Cmd. Sub cmd. Data Description
10* 00 发送/读取调谐步进 OFF Send/read the tuning step OFF
01 发送/读取 100 Hz 调谐步进 Send/read the 100 Hz tuning step
02 发送/读取 1 kHz 调谐步进 Send/read the 1 kHz tuning step
03 发送/读取 5 kHz 调谐步进 Send/read the 5 kHz tuning step
04 发送/读取 9 kHz 调谐步进 Send/read the 9 kHz tuning step
05 发送/读取 10 kHz 调谐步进 Send/read the 10 kHz tuning step
06 发送/读取 12.5 kHz 调谐步进 Send/read the 12.5 kHz tuning step
07 发送/读取 20 kHz 调谐步进 Send/read the 20 kHz tuning step
08 发送/读取 25 kHz 调谐步进 Send/read the 25 kHz tuning step
11* 00/20 发送/读取衰减器 *(00=OFF, 20=20dB ON) Send/read Attenuator *(00=OFF, 20=20dB ON)
13 00 用语音合成器播报全部数据 Speech all data with voice synthesizer
01 用语音合成器播报工作频率与 S 表电平 Speech the operating frequency and S meter level by voice synthesizer
02 用语音合成器播报工作模式 Speech the operating mode by voice synthesizer
14* 01 00 00 to 02 55 发送/读取 AF 音量 *(00 00=min. to 02 55=max.) Send/read the AF level *(00 00=min. to 02 55=max.)
02 00 00 to 02 55 发送/读取射频增益 *(00 00=min. to 02 55=max.) Send/read the RF gain level *(00 00=min. to 02 55=max.)
03 00 00 to 02 55 发送/读取静噪电平 *(00 00=min. to 02 55=max.) Send/read the squelch level *(00 00=min. to 02 55=max.)
Cmd. Sub cmd. Data 说明 Cmd. Sub cmd. Data Description
06 00 00 to 02 55 发送/读取 NR 电平 *(00 00=0% to 02 55=100%) Send/read the NR level *(00 00=0% to 02 55=100%)
07 00 00 to 02 55 发送/读取内圈 [TWIN PBT] 位置 *(00 00=max. CCW, 01 28=center, 02 55=max. CW) Send/read inner [TWIN PBT] position *(00 00=max. CCW, 01 28=center, 02 55=max. CW)
08 00 00 to 02 55 发送/读取外圈 [TWIN PBT] 位置 *(00 00=max. CCW, 01 28=center, 02 55=max. CW) Send/read outer [TWIN PBT] position *(00 00=max. CCW, 01 28=center, 02 55=max. CW)
09 00 00 to 02 55 发送/读取 CW 音调 *(00 00=300 Hz, 01 28=600 Hz, 02 55=900 Hz; 5 Hz steps) Send/read CW pitch *(00 00=300 Hz, 01 28=600 Hz, 02 55=900 Hz; 5 Hz steps)
0A 00 00 to 02 55 发送/读取 [RF PWR] 位置 *(00 00=max. CCW, 02 55=max. CW) Send/read [RF PWR] position *(00 00=max. CCW, 02 55=max. CW)
0B 00 00 to 02 55 发送/读取 [MIC] 位置 *(00 00=max. CCW, 02 55=max. CW) Send/read [MIC] position *(00 00=max. CCW, 02 55=max. CW)
0C 00 00 to 02 55 发送/读取 [KEY SPEED] 电平 *(00 00=6wpm, 02 55=48wpm) Send/read [KEY SPEED] level *(00 00=6wpm, 02 55=48wpm)
0D 00 00 to 02 55 发送/读取 [NOTCH] 位置 *(00 00=max. CCW, 01 28=center, 02 55=max. CW) Send/read [NOTCH] position *(00 00=max. CCW, 01 28=center, 02 55=max. CW)
0E 00 00 to 02 55 发送/读取 COMP 电平 *(00 00=0 to 02 55=10) Send/read the COMP level *(00 00=0 to 02 55=10)
0F 00 00 to 02 55 发送/读取 Break-IN 延迟设定 *(00 00=2.0d to 02 55=13.0d) Send/read the Break-IN Delay setting *(00 00=2.0d to 02 55=13.0d)
12 00 00 to 02 55 发送/读取 NB 电平 *(00 00=0% to 02 55=100%) Send/read NB level *(00 00=0% to 02 55=100%)
15 00 00 to 02 55 发送/读取监听增益 *(00 00=0% to 02 55=100%)
Cmd. Sub cmd. Data 说明 Cmd. Sub cmd. Data Description
Send/read the Monitor gain *(00 00=0% to 02 55=100%)
16 00 00 to 02 55 发送/读取 VOX 增益 *(00 00=0% to 02 55=100%) Send/read the VOX gain *(00 00=0% to 02 55=100%)
17 00 00 to 02 55 发送/读取 Anti VOX 增益 *(00 00=0% to 02 55=100%) Send/read the Anti VOX gain *(00 00=0% to 02 55=100%)
19 00 00 to 02 55 发送/读取 BRIGHT 电平 *(00 00=0%, 02 55=100%) Send/read BRIGHT level *(00 00=0%, 02 55=100%)
15 01 00/01 读取噪声静噪或 S 表静噪的状态 *(静噪关闭) Read noise or S-meter squelch status *(squelch close)
02 00 00 to 02 55 读取 S 表电平 *(00 00=S0, 01 20=S9, 02 41=S9+60dB) Read S-meter level *(00 00=S0, 01 20=S9, 02 41=S9+60dB)
05 00/01 读取各种静噪功能的状态 *(静噪关闭) Read various squelch function's status *(squelch closed)
07 00/01 读取 OVF 图标的状态 (00=消失, 01=出现) Read the OVF icon status (00=Disappears, 01=Appears)
11 00 00 to 02 55 读取 PO 表电平 *(00 00=0%, 01 43=50%, 02 13=100%) Read PO meter level *(00 00=0%, 01 43=50%, 02 13=100%)
12 00 00 to 02 55 读取 SWR 表电平 *(00 00=SWR1.0, 00 48=SWR1.5, 00 80=SWR2.0, 01 20=SWR3.0) Read SWR meter level *(00 00=SWR1.0, 00 48=SWR1.5, 00 80=SWR2.0, 01 20=SWR3.0)
13 00 00 to 02 55 读取 ALC 表电平 *(00 00=最小 to 01 20=最大) Read ALC meter level *(00 00=Min. to 01 20=Max.)
14 00 00 to 02 55 读取 COMP 表电平 *(00 00=0 dB, 01 30=15 dB, 02 41=30 dB) Read COMP meter level *(00 00=0 dB, 01 30=15 dB, 02 41=30 dB)
Cmd. Sub cmd. Data 说明 Cmd. Sub cmd. Data Description
15 00 00 to 02 55 读取 Vd 表电平 *(00 00=0 V, 00 13=10 V, 02 41=16 V) Read Vd meter level *(00 00=0 V, 00 13=10 V, 02 41=16 V)
16 00 00 to 02 55 读取 Id 表电平 *(00 00=0, 00 97=10, 01 46=15, 02 41=25) Read Id meter level *(00 00=0, 00 97=10, 01 46=15, 02 41=25)
16* 02 00 to 02 前置放大器 (00=OFF, 01=Preamp 1 ON, 02=Preamp 2 ON) Preamp (00=OFF, 01=Preamp 1 ON, 02=Preamp 2 ON)
12 01 to 03 AGC *(01=FAST, 02=MID, 03=SLOW) AGC *(01=FAST, 02=MID, 03=SLOW)
22 00/01 噪声消除器 *(00=OFF, 01=ON) Noise blanker *(00=OFF, 01=ON)
40 00/01 噪声抑制 *(00=OFF, 01=ON) Noise reduction *(00=OFF, 01=ON)
41 00/01 自动陷波功能 *(00=OFF, 01=ON) Auto notch function *(00=OFF, 01=ON)
42 00/01 中继亚音 *(00=OFF, 01=ON) Repeater tone *(00=OFF, 01=ON)
43 00/01 亚音静噪 *(00=OFF, 01=ON) Tone squelch *(00=OFF, 01=ON)
44 00/01 语音压缩器 *(00=OFF, 01=ON) Speech compressor *(00=OFF, 01=ON)
45 00/01 监听功能 *(00=OFF, 01=ON) Monitor function *(00=OFF, 01=ON)
46 00/01 VOX 功能 *(00=OFF, 01=ON) VOX function *(00=OFF, 01=ON)
47 00 to 02 插入（Break-in）功能 *(00=BK-IN OFF, 01=Semi BK-IN ON, 02=Full BK-IN ON) BK-IN function *(00=BK-IN OFF, 01=Semi BK-IN ON, 02=Full BK-IN ON)
48 00/01 手动陷波功能 *(00=OFF, 01=ON) Manual notch function *(00=OFF, 01=ON)
表 19-6 CI-V 命令表（Cmd 16* 续 ~ 1A*） CI-V command table (Cmd 16* cont. ~ 1A*)
Sub Cmd. cmd. Data 说明 Cmd. Sub Data Description cmd.
16* 4F 00/01 Twin Peak Filter *(00=OFF, 01=ON) 只有把 Mark 与 Shift 分别设为 2125 Hz 与 170 Hz 时才能设为 ON。 Twin Peak Filter *(00=OFF, 01=ON) Can be turned ON only when Mark and Shift are set to 2125 Hz and 170 Hz, respectively.
50 00/01 旋钮锁定功能 *(00=OFF, 01=ON) Dial lock function *(00=OFF, 01=ON)
56 00/01 DSP 滤波器类型 *(00=SHARP, 01=SOFT) DSP filter type *(00=SHARP, 01=SOFT)
57 00 to 02 手动陷波宽度 (00=WIDE, 01=MID, 02=NAR) Manual notch width (00=WIDE, 01=MID, 02=NAR)
58 00 to 02 SSB 发射带宽 (00=WIDE, 01=MID, 02=NAR) SSB transmit bandwidth (00=WIDE, 01=MID, 02=NAR)
65 00/01 发送 IP+ 功能设定 (00=OFF, 01=ON) Send the IP+ function setting (00=OFF, 01=ON)
66 00/01 发送/读取发射禁止（TX Inhibit）功能 (00=OFF, 01=ON) Send/read the TX Inhibit function (00=OFF, 01=ON)
17 p. 19-13 发送 CW 报文*2 Send CW messages*2
18 00 关闭收发信机电源 Turn OFF the transceiver
01 开启收发信机电源*3 Turn ON the transceiver*3
19 00 读取收发信机 ID Read the transceiver ID
1A* 00 p. 19-11 发送/读取存储内容 Send/read memory contents
01 p. 19-10 发送/读取波段堆叠寄存器内容 Send/read band stacking register contents
02 p. 19-12 发送/读取存储电键（Keyer）内容*1 Send/read memory keyer contents*1
Sub Cmd. cmd. Data 说明 Cmd. Sub Data Description cmd.
03 00 to 发送/读取所选滤波器的带宽 49 (AM: 00=200 Hz 到 49=10 kHz；AM 以外模式: 00=50 Hz 到 31/40=2700 Hz/3600 Hz) Send/read the selected filter width (AM: 00=200 Hz to 49=10 kHz; other than AM modes: 00=50 Hz to 31/40=2700 Hz/3600 Hz)
04 00 to 发送/读取所选 AGC 时间常数 13 *(00=OFF, AM: 01=0.3 sec. 到 13=8.0 sec., SSB,CW,RTTY:01=0.1 sec. 到 13=6.0 sec.) Send/read the selected AGC time constant *(00=OFF, AM: 01=0.3 sec. to 13=8.0 sec., SSB,CW,RTTY:01=0.1 sec. to 13=6.0 sec.)
表 19-7 CI-V 命令表（Cmd 1A* 05：接收、发射与音频设置） CI-V command table (Cmd 1A* 05: receive, transmit and audio settings)
Sub Cmd. Data 说明 cmd. Cmd. Data Description Sub cmd.
1A* 00 01 p. 19-9 发送/读取 SSB 接收 HPF/LPF 设定 05 Send/read SSB RX HPF/LPF settings
00 02 00 to 10 发送/读取 SSB 接收音调（低音）电平 (00=-5 到 10=+5) Send/read SSB RX Tone (Bass) level (00=-5 to 10=+5)
00 03 00 to 10 发送/读取 SSB 接收音调（高音）电平 (00=-5 到 10=+5) Send/read SSB RX Tone (Treble) level (00=-5 to 10=+5)
00 04 p. 19-9 发送/读取 AM 接收 HPF/LPF 设定 Send/read AM RX HPF/LPF settings
00 05 00 to 10 发送/读取 AM 接收音调（低音）电平 (00=-5 到 10=+5) Send/read AM RX Tone (Bass) level (00=-5 to 10=+5)
00 06 00 to 10 发送/读取 AM 接收音调（高音）电平 (00=-5 到 10=+5) Send/read AM RX Tone (Treble) level (00=-5 to 10=+5)
00 07 p. 19-9 发送/读取 FM 接收 HPF/LPF 设定 Send/read FM RX HPF/LPF settings
00 08 00 to 10 发送/读取 FM 接收音调（低音）电平 (00=-5 到 10=+5) Send/read FM RX Tone (Bass) level (00=-5 to 10=+5)
00 09 00 to 10 发送/读取 FM 接收音调（高音）电平 (00=-5 到 10=+5) Send/read FM RX Tone (Treble) level (00=-5 to 10=+5)
00 10 p. 19-9 发送/读取 CW 接收 HPF/LPF 设定 Send/read CW RX HPF/LPF settings
00 11 p. 19-9 发送/读取 RTTY 接收 HPF/LPF 设定 Send/read RTTY RX HPF/LPF settings
00 12 00 to 10 发送/读取 SSB 发射音调（低音）电平 (00=-5 到 10=+5) Send/read SSB TX Tone (Bass) level (00=-5 to 10=+5)
00 13 00 to 10 发送/读取 SSB 发射音调（高音）电平 (00=-5 到 10=+5) Send/read SSB TX Tone (Treble) level (00=-5 to 10=+5)
Sub Cmd. Data 说明 cmd. Cmd. Data Description Sub cmd.
00 14 p. 19-9 发送/读取 SSB 发射带宽（宽） Send/read SSB TX bandwidth for wide
00 15 p. 19-9 发送/读取 SSB 发射带宽（中） Send/read SSB TX bandwidth for mid
00 16 p. 19-9 发送/读取 SSB 发射带宽（窄） Send/read SSB TX bandwidth for narrow
00 17 00 to 10 发送/读取 AM 发射音调（低音）电平 (00=-5 到 10=+5) Send/read AM TX Tone (Bass) level (00=-5 to 10=+5)
00 18 00 to 10 发送/读取 AM 发射音调（高音）电平 (00=-5 到 10=+5) Send/read AM TX Tone (Treble) level (00=-5 to 10=+5)
00 19 00 to 10 发送/读取 FM 发射音调（低音）电平 (00=-5 到 10=+5) Send/read FM TX Tone (Bass) level (00=-5 to 10=+5)
00 20 00 to 10 发送/读取 FM 发射音调（高音）电平 (00=-5 到 10=+5) Send/read FM TX Tone (Treble) level (00=-5 to 10=+5)
00 21 00 00 to 02 55 发送/读取提示音音量 (00 00=min. 到 02 55=max.) Send/read beep gain (00 00=min. to 02 55=max.)
1A* 00 22 00/01 发送/读取提示音音量限制 *(00=OFF, 01=ON) 05 Send/read beep gain limit *(00=OFF, 01=ON)
00 23 00/01 发送/读取确认提示音 (00=OFF, 01=ON) Send/read confirmation beep (00=OFF, 01=ON)
1A* 00 24 00 发送/读取波段边界提示音 OFF 05 Send/read the band edge beep OFF
01 发送/读取波段边界提示音 ON (以默认业余波段鸣响) Send/read the band edge beep ON (Beep sounds with a default amateur band)
02 发送/读取波段边界提示音（用户设定）ON Send/read the band edge beep with user setting ON
03 发送/读取波段边界提示音（用户设定/发射限制）ON Send/read the band edge beep with user setting/TX limit ON
Sub Cmd. Data 说明 cmd. Cmd. Data Description Sub cmd.
1A* 00 25 00 to 02 发送/读取 RF/SQL 控制设定 05 (00=Auto, 01=SQL, 02=RF+SQL) Send/read the RF/SQL Control setting (00=Auto, 01=SQL, 02=RF+SQL)
1A* 00 26 00 to 05 发送/读取发射延时设定（HF） 05 (00=OFF, 01=10 ms, 02=15 ms, 03=20 ms, 04=25 ms, 05=30 ms) Send/read the TX Delay setting (HF) (00=OFF, 01=10 ms, 02=15 ms, 03=20 ms, 04=25 ms, 05=30 ms)
1A* 00 27 00 to 05 发送/读取发射延时设定（50 MHz） 05 (00=OFF, 01=10 ms, 02=15 ms, 03=20 ms, 04=25 ms, 05=30 ms) Send/read the TX Delay setting (50 MHz) (00=OFF, 01=10 ms, 02=15 ms, 03=20 ms, 04=25 ms, 05=30 ms)
1A* 00 28 00 to 05 发送/读取发射延时设定（70 MHz） 05 (00=OFF, 01=10 ms, 02=15 ms, 03=20 ms, 04=25 ms, 05=30 ms) Send/read the TX Delay setting (70 MHz) (00=OFF, 01=10 ms, 02=15 ms, 03=20 ms, 04=25 ms, 05=30 ms)
1A* 00 29 00 to 05 发送/读取发射超时定时器（TOT）设定 05 (00=OFF, 01=3 min., 02=5 min., 03=10min., 04=20 min., 05=30 min.) Send/read the Time-Out Timer setting (00=OFF, 01=3 min., 02=5 min., 03=10min., 04=20 min., 05=30 min.)
1A* 00 30 00/01 发送/读取快速异频设定 *(00=OFF, 01=ON) 05 Send/read quick split set *(00=OFF, 01=ON)
1A* 00 31 p. 19-10 发送/读取 HF 的 FM 异频偏移 -9.999 至 +9.999 MHz 05 Send/read FM split offset -9.999 to +9.999 MHz for HF
1A* 00 32 p. 19-10 发送/读取 50 MHz 的 FM 异频偏移 -9.999 至 +9.999 MHz 05 Send/read FM split offset -9.999 to +9.999 MHz for 50 MHz
1A* 00 33 00/01 发送/读取异频锁定设定 *(00=OFF, 01=ON) 05 Send/read split lock set *(00=OFF, 01=ON)
1A* 00 34 00/01 发送/读取 [TUNER] 开关设定 05 (00=Manual, 01=Auto) Send/read [TUNER] Switch set (00=Manual, 01=Auto)
1A* 00 35 00 or 01 发送/读取 PTT 调谐设定 *(00=OFF, 01=ON) 05 Send/read PTT tune set *(00=OFF, 01=ON)
1A* 00 36 00 to 02 发送/读取 RTTY 标记频率 05 (00=1275 Hz, 01=1615 Hz, 02=2125 Hz) Send/read RTTY mark frequency (00=1275 Hz, 01=1615 Hz, 02=2125 Hz)
1A* 00 37 00 to 02 发送/读取 RTTY 频移宽度 05 (00=170 Hz, 01=200 Hz, 02=425 Hz) Send/read RTTY shift width (00=170 Hz, 01=200 Hz, 02=425 Hz)
Sub Cmd. Data 说明 cmd. Cmd. Data Description Sub cmd.
1A* 00 38 00/01 发送/读取 RTTY 键控极性 05 (00=Normal, 01=Reverse) Send/read RTTY keying polarity (00=Normal, 01=Reverse)
1A* 00 39 00/01 发送/读取语音播报语言 05 (00=English, 01=Japanese) Send/read speech language (00=English, 01=Japanese)
1A* 00 40 00/01 发送/读取语音播报速度 (00=Low, 01=High) 05 Send/read speech speed (00=Low, 01=High)
1A* 00 41 00/01 发送/读取 S 电平语音播报 (00=OFF, 01=ON) 05 Send/read S-level speech (00=OFF, 01=ON)
1A* 00 42 00/01 发送/读取切换模式时语音播报 (00=OFF, 01=ON) 05 Send/read speech with a mode switch operation (00=OFF, 01=ON)
1A* 00 43 00 00 to 02 55 发送/读取语音播报音量 05 (00 00=0% 到 02 55=100%) Send/read speech level (00 00=0% to 02 55=100%)
1A* 00 44 00/01 发送/读取 [SPEECH/LOCK] 键功能设定 05 (00=按下: SPEECH, 长按: LOCK, 01=按下: LOCK, 长按: SPEECH) Send/read [SPEECH/LOCK] key function setting (00=Push: SPEECH, Hold down: LOCK, 01=Push: LOCK, Hold down: SPEECH)
1A* 00 45 00/01 发送/读取锁定功能设定 05 (00=MAIN DIAL, 01=PANEL) Send/read the Lock function setting (00=MAIN DIAL, 01=PANEL)
1A* 00 46 00/01 发送/读取备忘录（MPAD）数量 05 (00=5 ch, 01=10 ch) Send/read memo pad numbers (00=5 ch, 01=10 ch)
1A* 00 47 00 to 02 发送/读取主调谐旋钮自动调谐步进 05 (00=OFF, 01=Low, 02=High) Send/read main dial auto TS (00=OFF, 01=Low, 02=High)
1A* 00 48 00/01 发送/读取话筒 [UP]/[DOWN] 键速度 05 (00=Low, 01=High) Send/read mic. up/down speed (00=Low, 01=High)
1A* 00 49 00 or 01 发送/读取快速清除 RIT/∂TX 功能 05 (00=OFF, 01=ON) Send/read quick RIT/∂TX clear function (00=OFF, 01=ON)
1A* 00 50 00 to 02 发送/读取 SSB 陷波操作方式 05 *(00=Auto, 01=Manual, 02=Auto/Manual)
Sub Cmd. Data 说明 cmd. Cmd. Data Description Sub cmd.
Send/read SSB notch operation *(00=Auto, 01=Manual, 02=Auto/Manual)
1A* 00 51 00 to 02 发送/读取 AM 陷波操作方式 05 (00=Auto, 01=Manual, 02=Auto/Manual) Send/read AM notch operation (00=Auto, 01=Manual, 02=Auto/Manual)
1A* 00 52 00/01 发送/读取 SSB/CW 同步调谐功能 (00=OFF, 01=ON) 05 Send/read SSB/CW synchronous tuning function (00=OFF, 01=ON)
1A* 00 53 00/01 发送/读取 CW 正常边带设定 05 (00=LSB, 01=USB) Send/read CW normal side set (00=LSB, 01=USB)
1A* 00 54 00/01 发送/读取由 [POWER] 开关进行屏幕捕获 (00=OFF, 01=ON) 05 Send/read screen capture by the [POWER] switch (00=OFF, 01=ON)
1A* 00 55 00/01 发送/读取屏幕捕获图像数据的保存格式 (00=PNG format, 01=BMP format) 05 Send/read screen capture image data saving format (00=PNG format, 01=BMP format)
1A* 00 56 00/01 发送/读取键盘类型 05 (00=Ten-key, 01=Full Keyboard) Send/read keyboard type (00=Ten-key, 01=Full Keyboard)
1A* 00 57 00/01 发送/读取校准标记 05 (00=OFF, 01=ON) Send/read calibration marker (00=OFF, 01=ON)
1A* 00 58 00 00 to 02 55 发送/读取基准频率 05 (00 00=0%, 02 55=100%) Send/read reference frequency (00 00=0%,02 55=100%)
1A* 00 59 00 or 01 发送/读取送往 ACC/USB 的 AF/IF 信号输出 05 (00=AF, 01=IF) Send/read AF/IF signal output to ACC/USB (00=AF, 01=IF)
1A* 00 60 00 00 to 02 55 发送/读取送往 ACC/USB 的 AF 输出电平 05 (00 00=0% 到 02 55=100%) Send/read AF output level to ACC/USB (00 00=0% to 02 55=100%)
1A* 00 61 00/01 发送/读取送往 ACC/USB 的 AF 信号输出的静噪功能 05 (00=OFF (Open), 01=ON) Send/read squelch function for the AF signal output to ACC/USB (00=OFF (Open), 01=ON)
1A* 00 62 00/01 发送/读取送往 ACC/USB 的提示音与语音播报输出设定（设定 AF 信号输出时） 05 (00=OFF, 01=ON) Send/read beep and speech output setting to ACC/USB (when AF signal output is set)
Sub Cmd. Data 说明 cmd. Cmd. Data Description Sub cmd.
(00=OFF, 01=ON)
1A* 00 63 00 00 to 02 55 发送/读取送往 ACC/USB 的 IF 信号输出电平 05 (00 00=0%, 02 55=100%) Send/read IF signal output level to ACC/USB (00 00=0%, 02 55=100%)
1A* 00 64 00 00 to 02 55 发送/读取来自 ACC 的 MOD 输入电平 05 (00 00=0% 到 02 55=100%) Send/read MOD input level from ACC (00 00=0% to 02 55=100%)
1A* 00 65 00 00 to 02 55 发送/读取来自 USB 的 MOD 输入电平 05 (00 00=0% 到 02 55=100%) Send/read MOD input level from USB (00 00=0% to 02 55=100%)
1A* 00 66 00 to 04 发送/读取 DATA OFF 时的 MOD 输入接口 05 (00=MIC, 01=ACC, 02=MIC/ACC, 03=USB, 04=MIC/USB) Send/read MOD input connector during DATA OFF (00=MIC, 01=ACC, 02=MIC/ACC, 03=USB, 04=MIC/USB)
1A* 00 67 00 to 04 发送/读取 DATA 时的 MOD 输入接口 05 (00=MIC, 01=ACC, 02=MIC/ACC, 03=USB, 04=MIC/USB) Send/read MOD input connector during DATA (00=MIC, 01=ACC, 02=MIC/ACC, 03=USB, 04=MIC/USB)
1A* 00 68 00/01 发送/读取 VOICE 的外接键盘设定 *(00=OFF, 01=ON) 05 Send/read the external keypad setting for VOICE *(00=OFF, 01=ON)
1A* 00 69 00/01 发送/读取存储电键（Memory KEYER）的外接键盘设定 (00=OFF, 01=ON) 05 Send/read the external keypad setting for Memory KEYER (00=OFF, 01=ON)
1A* 00 70 00/01 发送/读取 RTTY Memory 的外接键盘设定 (00=OFF, 01=ON) 05 Send/read the external keypad setting for RTTY Memory (00=OFF, 01=ON)
1A* 00 71 00/01 发送/读取 CI-V transceive 设定 05 (00=OFF, 01=ON) Send/read the CI-V transceive setting (00=OFF, 01=ON)
1A* 00 72 00 00 to 02 23 以十六进制码发送/读取 USB 到 REMOTE 的 transceive CI-V 地址 05 (00 00=00h 到 02 23=DFh) Send/read the transceive CI-V Address for USB to REMOTE in hexadecimal code (00 00=00h to 02 23=DFh)
1A* 00 73 00/01 发送/读取 CI-V Output（for ANT）功能 05 (00=OFF, 01=ON) Send/read the CI-V Output (for ANT) capability (00=OFF, 01=ON)
1A* 00 74 00/01 发送/读取 CI-V USB 端口设定 05 (00=Link to [REMOTE], 01=Unlink to [REMOTE])（只读） Send/read the CI-V USB port setting (00=Link to [REMOTE], 01=Unlink to [REMOTE]) (Read only)
Sub Cmd. Data 说明 cmd. Cmd. Data Description Sub cmd.
1A* 00 75 00/01 发送/读取来自 USB 的 CI-V 操作回显（echo back）设定 05 (00=ON, 01=OFF) Send/read echo back setting for CI-V operation from USB (00=ON, 01=OFF)
1A* 00 76 00/01 发送/读取 USB（串口）功能设定 05 (00=CI-V, 01=RTTY Decode) Send/read the USB (serial port) function setting (00=CI-V, 01=RTTY Decode)
1A* 00 77 00 to 03 发送/读取 RTTY 解码输出的数据传输速率 05 (00=4800 bps, 01=9600 bps, 02=19200 bps, 03=38400 bps) Send/read data transfer speed for RTTY decode output (00=4800 bps, 01=9600 bps, 02=19200 bps, 03=38400 bps)
1A* 00 78 00 to 02 发送/读取 USB 的发射控制线设定 05 (00=OFF, 01=DTR, 02=RTS) • 必须与 CW 键控和 RTTY（FSK）设定不同的线。 Send/read transmission control line setting for USB (00=OFF, 01=DTR, 02=RTS) • Different line must be set from both CW keying and RTTY (FSK)
1A* 00 79 00 to 02 发送/读取 USB 的 CW 键控线设定 05 (00=OFF, 01= DTR, 02=RTS) • 必须与发射控制和 RTTY（FSK）设定不同的线。 Send/read CW keying line setting for USB (00=OFF, 01= DTR, 02=RTS) • Different line must be set from both transmission control and RTTY (FSK)
1A* 00 80 00 to 02 发送/读取 USB 的 RTTY（FSK）线设定 05 (00=OFF, 01=DTR, 02=RTS) • 必须与 CW 键控和发射控制设定不同的线。 Send/read RTTY (FSK) line setting for USB (00=OFF, 01=DTR, 02=RTS) • Different line must be set from both CW keying and transmission control"
1A* 00 81 00 00 to 02 55 发送/读取 LCD 单元背光亮度 05 (00 00=0% 到 02 55=100%) Send/read LCD unit backlight brightness (00 00=0% to 02 55=100%)
1A* 00 82 00/01 发送/读取屏幕图像类型 (00=A, 01=B) 05 Send/read screen image type (00=A, 01=B)
1A* 00 83 00/01 发送/读取频率显示字体 05 (00=Basic, 01=Round) Send/read frequency readout font (00=Basic, 01=Round)
1A* 00 84 00/01 发送/读取仪表峰值保持 05 *(00=OFF, 01=ON) Send/read peak hold set for meter *(00=OFF, 01=ON)
1A* 00 85 00/01 发送/读取存储名称显示设定 05 (00=OFF, 01=ON)
Sub Cmd. Data 说明 cmd. Cmd. Data Description Sub cmd.
Send/read memory name indication setting (00=OFF, 01=ON)
1A* 00 86 00/01 发送/读取手动陷波宽度弹出显示设定 (00=OFF, 01=ON) 05 Send/read manual notch width pop-up indication setting (00=OFF, 01=ON)
1A* 00 87 00/01 发送/读取旋转 [TWIN PBT] 时 PBT 偏移值的显示设定 (00=OFF, 01=ON) 05 Send/read PBT shifting value display setting while rotating [TWIN PBT] (00=OFF, 01=ON)
1A* 00 88 00/01 发送/读取切换 IF 滤波器时 IF 滤波器宽度与偏移值的显示设定 05 (00=OFF, 01=ON) Send/read IF filter width and shifting value display setting when the IF filter is switched (00=OFF, 01=ON)
1A* 00 89 00 to 03 发送/读取屏幕保护（屏保）功能 05 (00=OFF, 01=15 minutes, 02=30 minutes, 03=60 minutes) Send/read screen saver function (00=OFF, 01=15 minutes, 02=30 minutes, 03=60 minutes)
1A* 00 90 00/01 发送/读取开机问候语显示 05 (00=OFF, 01=ON) Send/read opening message indication (00=OFF, 01=ON)
1A* 00 91 p. 19-10 发送/读取开机问候语内容 05 (最多 10 个字符) Send/read opening message contents (up to 10-character)
1A* 00 92 00/01 发送/读取开机确认（Power ON Check）设定 05 (00=OFF, 01=ON) Send/read Power ON Check setting (00=OFF, 01=ON)
1A* 00 93 00/01 发送/读取显示语言 05 (00=English, 01=Japanese) Send/read Display Language (00=English, 01=Japanese)
1A* 00 94 20 00 01 01 to 20 99 12 发送/读取日期设定 05 31 (20 00 01 01=2000/01/01 到 20 99 12 31=2099/12/31) Send/read date setting (20 00 01 01=2000/01/01 to 20 99 12 31=2099/12/31)
1A* 00 95 00 00 to 23 59 发送/读取时间设定 05 (00 00=00:00 到 23 59=23:59) Send/read time setting (00 00=00:00 to 23 59=23:59)
1A* 00 96 p. 19-13 发送/读取 UTC 时差 05 Send/read UTC offset time
1A* 00 97 00/01 发送/读取发射时的Scope 显示 05 (00=OFF, 01=ON)
Sub Cmd. Data 说明 cmd. Cmd. Data Description Sub cmd.
Send/read scope indication during TX (00=OFF, 01=ON)
1A* 00 98 00 to 02 发送/读取 Scope 最大保持 05 (00=OFF, 01=ON) Send/read scope max. hold (00=OFF, 01=ON)
1A* 00 99 00 to 02 发送/读取 Scope 中心频率设定 05 (00=Filter center, 01=Carrier point center, 02=Carrier point center (Abs. Freq.) Send/read scope center frequency set (00=Filter center, 01=Carrier point center, 02=Carrier point center (Abs. Freq.)
表 19-8 CI-V 命令表（Cmd 1A* 05：Scope、RTTY、录音与前面板按键） CI-V command table (Cmd 1A* 05: Scope, RTTY, recorder and front panel keys)
Sub Cmd. cmd. Data 说明 Cmd. Sub Data Description cmd.
1A* 01 00 00/01 发送/读取 Scope 标记位置（FIX Type/SCROLL Type）设定 05 (00=Filter center, 01 Carrier point) Send/read scope marker position (FIX Type/SCROLL Type) setting (00=Filter center, 01 Carrier point)
01 01 00/01 发送/读取外部监视信号宽度 (00=Narrow, 01=Wide) Send/read external monitor signal width (00=Narrow, 01=Wide)
01 02 00 to 03 发送/读取频谱Scope 的平均功能 (00=OFF, 01=2, 02=3, 03=4) Send/read averaging function for spectrum scope (00=OFF, 01=2, 02=3, 03=4)
01 03 00/01 发送/读取频谱显示类型 (00=Fill, 01=Fill+Line) Send/read spectrum display type (00=Fill, 01=Fill+Line)
01 04 p. 19-9 发送/读取频谱填充颜色 Send/read spectrum fill color
01 05 p. 19-9 发送/读取频谱线条颜色 Send/read spectrum line color
01 06 p. 19-9 发送/读取频谱峰值保持的颜色 Send/read spectrum color for peak hold
01 07 00/01 发送/读取频谱 Scope 的瀑布图设定 (00=OFF, 01=ON) Send/read waterfall set for spectrum scope (00=OFF, 01=ON)
01 08 00 to 02 发送/读取瀑布图速度 (00=Slow, 01=Mid, 02=Fast) Send/read waterfall speed (00=Slow, 01=Mid, 02=Fast)
01 09 00 to 02 发送/读取选择放大Scope 时的瀑布图高度 (00=Small, 01=Mid, 02=Larger) Send/read waterfall height when expanded scope is selected (00=Small, 01=Mid, 02=Larger)
01 10 00 to 07 发送/读取频谱 Scope 瀑布图的峰值颜色电平设定 (00=Grid 1, 01=Grid 2, 02=Grid 3, 03=Grid 4, 04=Grid 5, 05=Grid 6, 06=Grid 7, 07=Grid 8) Send/read peak color level set for waterfall of the spectrum scope (00=Grid 1, 01=Grid 2, 02=Grid 3, 03=Grid 4, 04=Grid 5, 05=Grid 6, 06=Grid 7, 07=Grid 8)
Sub Cmd. cmd. Data 说明 Cmd. Sub Data Description cmd.
01 11 00/01 发送/读取 Scope 瀑布图标记的自动隐藏 (00=OFF, 01=ON) Send/read scope waterfall marker auto-hide (00=OFF, 01=ON)
1A* 01 12 p. 19-9 发送/读取 0.03 至 1.60 MHz 波段的 Scope 边界 1 频率 05 Send/read scope edge 1 frequencies for 0.03 to 1.60 MHz band
1A* 01 13 p. 19-9 发送/读取 0.03 至 1.60 MHz 波段的 Scope 边界 2 频率 05 Send/read scope edge 2 frequencies for 0.03 to 1.60 MHz band
1A* 01 14 p. 19-9 发送/读取 0.03 至 1.60 MHz 波段的 Scope 边界 3 频率 05 Send/read scope edge 3 frequencies for 0.03 to 1.60 MHz band
1A* 01 15 p. 19-9 发送/读取 1.60 至 2.00 MHz 波段的 Scope 边界 1 频率 05 Send/read scope edge 1 frequencies for 1.60 to 2.00 MHz band
1A* 01 16 p. 19-9 发送/读取 1.60 至 2.00 MHz 波段的 Scope 边界 2 频率 05 Send/read scope edge 2 frequencies for 1.60 to 2.00 MHz band
1A* 01 17 p. 19-9 发送/读取 1.60 至 2.00 MHz 波段的 Scope 边界 3 频率 05 Send/read scope edge 3 frequencies for 1.60 to 2.00 MHz band
1A* 01 18 p. 19-9 发送/读取 2.00 至 6.00 MHz 波段的 Scope 边界 1 频率 05 Send/read scope edge 1 frequencies for 2.00 to 6.00 MHz band
1A* 01 19 p. 19-9 发送/读取 2.00 至 6.00 MHz 波段的 Scope 边界 2 频率 05 Send/read scope edge 2 frequencies for 2.00 to 6.00 MHz band
1A* 01 20 p. 19-9 发送/读取 2.00 至 6.00 MHz 波段的 Scope 边界 3 频率 05 Send/read scope edge 3 frequencies for 2.00 to 6.00 MHz band
1A* 01 21 p. 19-9 发送/读取 6.00 至 8.00 MHz 波段的 Scope 边界 1 频率 05 Send/read scope edge 1 frequencies for 6.00 to 8.00 MHz band
1A* 01 22 p. 19-9 发送/读取 6.00 至 8.00 MHz 波段的 Scope 边界 2 频率 05 Send/read scope edge 2 frequencies for 6.00 to 8.00 MHz band
1A* 01 23 p. 19-9 发送/读取 6.00 至 8.00 MHz 波段的 Scope 边界 3 频率 05 Send/read scope edge 3 frequencies for 6.00 to 8.00 MHz band
1A* 01 24 p. 19-9 发送/读取 8.00 至 11.00 MHz 波段的 Scope 边界 1 频率 05 Send/read scope edge 1 frequencies for 8.00 to 11.00 MHz band
1A* 01 25 p. 19-9 发送/读取 8.00 至 11.00 MHz 波段的 Scope 边界 2 频率 05 Send/read scope edge 2 frequencies for 8.00 to 11.00 MHz band
1A* 01 26 p. 19-9 发送/读取 8.00 至 11.00 MHz 波段的 Scope 边界 3 频率 05 Send/read scope edge 3 frequencies for 8.00 to 11.00 MHz band
1A* 01 27 p. 19-9 发送/读取 11.00 至 15.00 MHz 波段的 Scope 边界 1 频率 05 Send/read scope edge 1 frequencies for 11.00 to 15.00 MHz band
1A* 01 28 p. 19-9 发送/读取 11.00 至 15.00 MHz 波段的 Scope 边界 2 频率 05 Send/read scope edge 2 frequencies for 11.00 to 15.00 MHz band
Sub Cmd. cmd. Data 说明 Cmd. Sub Data Description cmd.
1A* 01 29 p. 19-9 发送/读取 11.00 至 15.00 MHz 波段的 Scope 边界 3 频率 05 Send/read scope edge 3 frequencies for 11.00 to 15.00 MHz band
1A* 01 30 p. 19-9 发送/读取 15.00 至 20.00 MHz 波段的 Scope 边界 1 频率 05 Send/read scope edge 1 frequencies for 15.00 to 20.00 MHz band
1A* 01 31 p. 19-9 发送/读取 15.00 至 20.00 MHz 波段的 Scope 边界 2 频率 05 Send/read scope edge 2 frequencies for 15.00 to 20.00 MHz band
1A* 01 32 p. 19-9 发送/读取 15.00 至 20.00 MHz 波段的 Scope 边界 3 频率 05 Send/read scope edge 3 frequencies for 15.00 to 20.00 MHz band
1A* 01 33 p. 19-9 发送/读取 20.00 至 22.00 MHz 波段的 Scope 边界 1 频率 05 Send/read scope edge 1 frequencies for 20.00 to 22.00 MHz band
1A* 01 34 p. 19-9 发送/读取 20.00 至 22.00 MHz 波段的 Scope 边界 2 频率 05 Send/read scope edge 2 frequencies for 20.00 to 22.00 MHz band
1A* 01 35 p. 19-9 发送/读取 20.00 至 22.00 MHz 波段的 Scope 边界 3 频率 05 Send/read scope edge 3 frequencies for 20.00 to 22.00 MHz band
1A* 01 36 p. 19-9 发送/读取 22.00 至 26.00 MHz 波段的 Scope 边界 1 频率 05 Send/read scope edge 1 frequencies for 22.00 to 26.00 MHz band
1A* 01 37 p. 19-9 发送/读取 22.00 至 26.00 MHz 波段的 Scope 边界 2 频率 05 Send/read scope edge 2 frequencies for 22.00 to 26.00 MHz band
1A* 01 38 p. 19-9 发送/读取 22.00 至 26.00 MHz 波段的 Scope 边界 3 频率 05 Send/read scope edge 3 frequencies for 22.00 to 26.00 MHz band
1A* 01 39 p. 19-9 发送/读取 26.00 至 30.00 MHz 波段的 Scope 边界 1 频率 05 Send/read scope edge 1 frequencies for 26.00 to 30.00 MHz band
1A* 01 40 p. 19-9 发送/读取 26.00 至 30.00 MHz 波段的 Scope 边界 2 频率 05 Send/read scope edge 2 frequencies for 26.00 to 30.00 MHz band
1A* 01 41 p. 19-9 发送/读取 26.00 至 30.00 MHz 波段的 Scope 边界 3 频率 05 Send/read scope edge 3 frequencies for 26.00 to 30.00 MHz band
1A* 01 42 p. 19-9 发送/读取 30.00 至 45.00 MHz 波段的 Scope 边界 1 频率 05 Send/read scope edge 1 frequencies for 30.00 to 45.00 MHz band
1A* 01 43 p. 19-9 发送/读取 30.00 至 45.00 MHz 波段的 Scope 边界 2 频率 05 Send/read scope edge 2 frequencies for 30.00 to 45.00 MHz band
1A* 01 44 p. 19-9 发送/读取 30.00 至 45.00 MHz 波段的 Scope 边界 2 频率 05 Send/read scope edge 2 frequencies for 30.00 to 45.00 MHz band
1A* 01 45 p. 19-9 发送/读取 45.00 至 60.00 MHz 波段的 Scope 边界 1 频率 05 Send/read scope edge 1 frequencies for 45.00 to 60.00 MHz band
1A* 01 46 p. 19-9 发送/读取 45.00 至 60.00 MHz 波段的 Scope 边界 2 频率 05 Send/read scope edge 2 frequencies for 45.00 to 60.00 MHz band
1A* 01 47 p. 19-9 发送/读取 45.00 至 60.00 MHz 波段的 Scope 边界 3 频率 05 Send/read scope edge 3 frequencies for 45.00 to 60.00 MHz band
Sub Cmd. cmd. Data 说明 Cmd. Sub Data Description cmd.
1A* 01 48 p. 19-9 发送/读取 60.00 至 74.80 MHz 波段的 Scope 边界 1 频率 05 Send/read scope edge 1 frequencies for 60.00 to 74.80 MHz band
1A* 01 49 p. 19-9 发送/读取 60.00 至 74.80 MHz 波段的 Scope 边界 2 频率 05 Send/read scope edge 2 frequencies for 60.00 to 74.80 MHz band
1A* 01 50 p. 19-9 发送/读取 60.00 至 74.80 MHz 波段的 Scope 边界 3 频率 05 Send/read scope edge 3 frequencies for 60.00 to 74.80 MHz band
1A* 01 51 00/01 发送/读取音频 FFT Scope 显示类型 05 (00=Fill, 01=Fill+Line) Send/read audio FFT scope display type (00=Fill, 01=Fill+Line)
1A* 01 52 p. 19-9 发送/读取音频 FFT Scope 波形颜色 05 Send/read the Audio FFT scope waveform color
1A* 01 53 00/01 发送/读取音频 FFT Scope 瀑布图显示 05 (00=OFF, 01=ON) Send/read the Audio FFT scope waterfall display (00=OFF, 01=ON)
1A* 01 54 p. 19-9 发送/读取音频示波器 Scope 波形颜色 05 Send/read the Audio Oscilloscope scope waveform color
1A* 01 55 00 竞赛号码样式的普通选择 05 Normal selection for contest number style
01 竞赛号码样式的「190→ANO」选择 "190→ANO" selection for contest number style
02 竞赛号码样式的「190→ANT」选择 "190→ANT" selection for contest number style
03 竞赛号码样式的「90→NO」选择 "90→NO" selection for contest number style
04 竞赛号码样式的「90→NT」选择 "90→NT" selection for contest number style
1A* 01 56 01 to 08 发送/读取计数触发通道 05 (01=M1, 02=M2, 03=M3, 04=M4, 05=M5, 06=M6, 07=M7, 08=M8) Send/read count up trigger channel (01=M1, 02=M2, 03=M3, 04=M4, 05=M5, 06=M6, 07=M7, 08=M8)
1A* 01 57 00 01 to 发送/读取当前号码 05 99 99 (00 01=1 到 99 99=9999) Send/read present number (00 01=1 to 99 99=9999)
1A* 01 58 00 00 to 发送/读取 CW 侧音音量 05 02 55 (00 00=0% 到 02 55=100%) Send/read CW side tone gain (00 00=0% to 02 55=100%)
Sub Cmd. cmd. Data 说明 Cmd. Sub Data Description cmd.
1A* 01 59 00/01 发送/读取 CW 侧音音量限制 05 (00=OFF, 01=ON) Send/read CW side tone gain limit (00=OFF, 01=ON)
1A* 01 60 01 to 60 发送/读取 CW 电键重复时间 05 (01=1 sec. 到 60=60 sec.) Send/read CW keyer repeat time (01=1 sec. to 60=60 sec.)
1A* 01 61 28 to 45 发送/读取 CW 电键点划比 05 (28=1:1:2.8 到 45=1:1:4.5) Send/read CW keyer dot/dash ratio (28=1:1:2.8 to 45=1:1:4.5)
1A* 01 62 00 to 03 发送/读取上升时间 05 (00=2 msec., 01=4 msec., 02=6 msec., 03=8 msec.) Send/read rise time (00=2 msec., 01=4 msec., 02=6 msec., 03=8 msec.)
1A* 01 63 00/01 发送/读取电键（paddle）极性 05 (00=Normal, 01=Reverse) Send/read paddle polarity (00=Normal, 01=Reverse)
1A* 01 64 00 to 02 发送/读取电键类型 05 (00=Straight, 01=Bug, 02=Paddle) Send/read keyer type (00=Straight, 01=Bug, 02=Paddle)
1A* 01 65 00/01 发送/读取话筒 [UP]/[DOWN] 键的电键功能 05 (00=OFF, 01=ON) Send/read mic. up/down keyer set (00=OFF, 01=ON)
1A* 01 66 00 to 03 发送/读取 RTTY FFT Scope 的平均功能 05 (00=OFF, 01=2, 02=3, 03=4) Send/read averaging function for RTTY FFT scope (00=OFF, 01=2, 02=3, 03=4)
1A* 01 67 p. 19-9 发送/读取 RTTY FFT Scope 波形颜色 05 Send/read RTTY FFT scope waveform color
1A* 01 68 00/01 发送/读取 RTTY 解码 USOS 05 (00=OFF, 01=ON) Send/read RTTY decode USOS (00=OFF, 01=ON)
1A* 01 69 00/01 发送/读取 RTTY 解码换行代码 05 (00=CR,LF,CR+LF, 01=CR+LF) Send/read RTTY decode new line code (00=CR,LF,CR+LF, 01=CR+LF)
1A* 01 70 00/01 发送/读取 RTTY 发射 USOS 05 (00=OFF, 01=ON)
Sub Cmd. cmd. Data 说明 Cmd. Sub Data Description cmd.
Send/read RTTY TX USOS (00=OFF, 01=ON)
1A* 01 71 p. 19-9 发送/读取接收 RTTY 文字的字体颜色 05 Send/read received RTTY text font color
1A* 01 72 p. 19-9 发送/读取发射 RTTY 文字的字体颜色 05 Send/read transmitted RTTY text font color
1A* 01 73 00/01 发送/读取 RTTY 记录功能 05 (00=OFF, 01=ON) Send/read RTTY log function (00=OFF, 01=ON)
1A* 01 74 00/01 发送/读取 RTTY 记录的文件保存格式 05 (00=Text, 01=HTML) Send/read file saving format for the RTTY log (00=Text, 01=HTML)
1A* 01 75 00/01 发送/读取 RTTY 时间戳设定 05 (00=OFF, 01=ON) Send/read RTTY time stamp set (00=OFF, 01=ON)
1A* 01 76 00/01 发送/读取 RTTY 解码记录的时间戳 05 (00=Local, 01=UTC) Send/read RTTY Decode Log Time Stamp (00=Local, 01=UTC)
1A* 01 77 00/01 发送/读取 RTTY 频率标记 05 (00=OFF, 01=ON) Send/read RTTY frequency stamp (00=OFF, 01=ON)
1A* 01 78 00/01 发送/读取扫描速度 (00=Low, 01=High) 05 Send/read scan speed (00=Low, 01=High)
1A* 01 79 00/01 发送/读取扫描继续功能 (00=OFF, 01=ON) 05 Send/read scan resume (00=OFF, 01=ON)
1A* 01 80 00/01 发送/读取发射已录语音存储时的自动监听功能设定 05 (00=OFF, 01=ON) Send/read auto monitor function setting when transmitting a recorded voice memory (00=OFF, 01=ON)
1A* 01 81 01/15 发送/读取重发已录语音的间隔 05 (01=1 sec. 到 15=15 sec.) Send/read repeat interval to transmit recorded voice audio (01=1 sec. to 15=15 sec.)
1A* 01 82 00/01 发送/读取 QSO 录音器的录音模式 05 (00=TX&RX, 01=RX Only) Send/read recording mode for QSO recorder (00=TX&RX, 01=RX Only)
Sub Cmd. cmd. Data 说明 Cmd. Sub Data Description cmd.
1A* 01 83 00/01 发送/读取 QSO 录音器的发射音频录音 05 (00=Microphone audio, 01=TX monitor audio) Send/read recording TX audio for QSO recorder (00=Microphone audio, 01=TX monitor audio)
1A* 01 84 00/01 发送/读取 QSO 录音器接收音频录音与静噪的关系 05 (00=Always, 01=Squelch Auto) Send/read squelch relation to recording RX audio for QSO recorder (00=Always, 01=Squelch Auto)
1A* 01 85 00/01 发送/读取 QSO 记录文件分割功能设定 05 (00=OFF, 01=ON) Send/read QSO record file split function setting (00=OFF, 01=ON)
1A* 01 86 00/01 发送/读取 PTT 自动录音功能设定 05 (00=OFF, 01=ON) Send/read PTT Automatic Recording function setting (00=OFF, 01=ON)
1A* 01 87 00 to 03 发送/读取 PTT 自动录音功能的接收音频录音状态 05 (00=OFF（不录音接收音频）, 01=录音前 5 sec. 的接收音频, 02=录音前 10 sec. 的接收音频, 03= 录音前 15 sec. 的接收音频) Send/read RX audio recording status for PTT Automatic Recording function (00=OFF (records no RX audio), 01=Records the RX audio just before 5 sec., 02=Records the RX audio just before 10 sec., 03=Records the RX audio just before 15 sec.)
1A* 01 88 00 to 03 发送/读取 QSO PLAY 跳过时间 05 (00=3 sec., 01=5 sec., 02=10 sec., 03=30 sec.) Send/read QSO PLAY Skip time (00=3 sec., 01=5 sec., 02=10 sec., 03=30 sec.)
1A* 01 89 00 to 09 发送/读取 NB 深度 (00=1 到 09=10) 05 Send/read NB depth (00=1 to 09=10)
1A* 01 90 00 00 to 发送/读取 NB 宽度 (00 00=1 到 02 55=100) 05 02 55 Send/read NB width (00 00=1 to 02 55=100)
1A* 01 91 00 to 20 发送/读取 VOX 延迟 05 (00=0.0 sec. 到 20=2.0 sec.) Send/read VOX delay (00=0.0 sec. to 20=2.0 sec.)
1A* 01 92 00 to 03 发送/读取 VOX 语音延迟 05 (00=OFF, 01=Short, 02=Mid., 03=Long) Send/read VOX voice delay (00=OFF, 01=Short, 02=Mid., 03=Long)
1A* 01 93 00/01 发送/读取 MF 波段衰减器设定 05 (00=OFF, 01=ON) Send/read the MF band attenuator setting (00=OFF, 01=ON)
1A* 01 94 00 to 02 发送/读取屏幕键盘布局 05 (00=English, 01=German, 02=French)
Sub Cmd. cmd. Data 说明 Cmd. Sub Data Description cmd.
Send/read on-screen keyboard layout (00=English, 01=German, 02=French)
1A* 01 95 00 00 to 发送/读取 VOICE TX 功能的发射语音音量 05 02 55 (00 00=0% 到 02 55=100%) Send/read the Transmit voice level for the VOICE TX function (00 00=0% to 02 55=100%)
1A* 01 96 p. 19-9 发送/读取 SSB-D 发射带宽 05 Send/read SSB-D TX bandwidth
1A* 01 97 00/01 USB 连接时的抑制定时器 05 (00=OFF, 01=ON) Inhibit Timer at USB connection (00=OFF, 01=ON)
1A* 01 98 p. 19-12 发送/读取前面板按键自定义 [VOX/BK-IN] 设定 05 Send/read the Front key customize [VOX/BK-IN] setting
1A* 01 99 p. 19-12 发送/读取前面板按键自定义 [AUTOTUNE] 设定 05 Send/read the Front key customize [AUTOTUNE] setting
1A* 02 00 p. 19-12 发送/读取前面板按键自定义 [▲] 设定 05 Send/read the Front key customize [▲] setting
1A* 02 01 p. 19-12 发送/读取前面板按键自定义 [▼] 设定 05 Send/read the Front key customize [▼] setting
1A* 02 02 p. 19-12 发送/读取 MIC 按键自定义 [UP] 设定 05 Send/read the MIC key customize [UP] setting
1A* 02 03 p. 19-12 发送/读取 MIC 按键自定义 [DOWN] 设定 05 Send/read the MIC key customize [DOWN] setting
1A* 02 04 p. 19-9 发送/读取 0.03 – 1.60 MHz 的 Scope 边界 4 频率 05 Send/read scope edge 4 frequencies for 0.03 – 1.60 MHz
1A* 02 05 p. 19-9 发送/读取 1.60 – 2.00 MHz 的 Scope 边界 4 频率 05 Send/read scope edge 4 frequencies for 1.60 – 2.00 MHz
1A* 02 06 p. 19-9 发送/读取 2.00 – 6.00 MHz 的 Scope 边界 4 频率 05 Send/read scope edge 4 frequencies for 2.00 – 6.00 MHz
1A* 02 07 p. 19-9 发送/读取 6.00 – 8.00 MHz 的 Scope 边界 4 频率 05 Send/read scope edge 4 frequencies for 6.00 – 8.00 MHz
1A* 02 08 p. 19-9 发送/读取 8.00 – 11.00 MHz 的 Scope 边界 4 频率 05 Send/read scope edge 4 frequencies for 8.00 – 11.00 MHz
1A* 02 09 p. 19-9 发送/读取 11.00 – 15.00 MHz 的 Scope 边界 4 频率 05 Send/read scope edge 4 frequencies for 11.00 – 15.00 MHz
1A* 02 10 p. 19-9 发送/读取 15.00 – 20.00 MHz 的 Scope 边界 4 频率 05 Send/read scope edge 4 frequencies for 15.00 – 20.00 MHz
1A* 02 11 p. 19-9 发送/读取 20.00 – 22.00 MHz 的 Scope 边界 4 频率 05 Send/read scope edge 4 frequencies for 20.00 – 22.00 MHz
Sub Cmd. cmd. Data 说明 Cmd. Sub Data Description cmd.
1A* 02 12 p. 19-9 发送/读取 22.00 – 26.00 MHz 的 Scope 边界 4 频率 05 Send/read scope edge 4 frequencies for 22.00 – 26.00 MHz
1A* 02 13 p. 19-9 发送/读取 26.00 – 30.00 MHz 的 Scope 边界 4 频率 05 Send/read scope edge 4 frequencies for 26.00 – 30.00 MHz
1A* 02 14 p. 19-9 发送/读取 30.00 – 45.00 MHz 的 Scope 边界 4 频率 05 Send/read scope edge 4 frequencies for 30.00 – 45.00 MHz
1A* 02 15 p. 19-9 发送/读取 45.00 – 60.00 MHz 的 Scope 边界 4 频率 05 Send/read scope edge 4 frequencies for 45.00 – 60.00 MHz
1A* 02 16 p. 19-9 发送/读取 60.00 – 74.80 MHz 的 Scope 边界 4 频率 05 Send/read scope edge 4 frequencies for 60.00 – 74.80 MHz
1A* 02 17 00/01 发送/读取 PTT 端口功能设定 05 00=PTT Input 01=PTT Input + SEND Output Send/read PTT Port Function setting 00=PTT Input 01=PTT Input + SEND Output
1A* 02 06 p. 19-10 发送/读取 DATA 模式设定 05 Send/read DATA mode setting
1A* 02 07 00/01 发送/读取 IP+ 功能设定 05 (00=OFF, 01=ON) Send/read IP+ function setting (00=OFF, 01=ON)